PSM 200 Personal Monitor System

The entry to professional in ear personal monitoring from Shure. This package contains SE112 Sound Isolating Earphones, a P2R Bodypack Receiver and a P2T TransMixer.


Why is in ear monitoring more effective than using a wedge speaker on stage?

Using a Shure monitoring system allows you to hear the music via your earphones at the exact time it is played. There can be a short delay in music coming out of the wedge, which can cause performers to play out of time. Wedge monitors will sound fine when standing in one position, but if you move to the left or right, that sound is likely to change. With in ear personal monitoring, the sound will be constant and comes with you, wherever you go. Using wedge monitors long term can also be damaging to your ears. Using Shure sound isolating earphones cuts out the sound around you leaving you to focus on playing in time.

How do I set up my PSM 200 in ear system?

Simply connect two line-level or mic–level inputs directly into the transmixer. Set the frequency on the transmixer using a single button, and the same again on the bodypack receiver. Connect your earphones to the P2R, set up your desired mix using the personal mix controls on the front of the transmixer and you are now all ready to go.
 

SKUs:

P2TR112GR PSM200 Wireless Monitoring System with SE112 Sound Isolating Earphones

P2T

PSM200 Wireless TransMixer
P2R PSM200 Bodypack Receiver

Components

P2T Wireless TransMixer

The P2T radio TransMixer is a transmitter and mixer in one unit. This forms part of the PSM200 in-ear personal monitoring system

SE112

The perfect audio upgrade for today’s portable digital devices, providing great sound with deep bass with impressive sound isolation.

The entry to professional in ear personal monitoring from Shure. This package contains SE112 Sound Isolating Earphones, a P2R Bodypack Receiver and a P2T TransMixer.

Key Features

  • Built-in audio limiter
  • Front mounted antenna
  • Two mic/line input channels for mix control
  • Built in headphone limiter
  • Volume control on bodypack receiver
  • 1/2 Rack space

System technical specifications

  • Wired Bodypack Option: Yes

Further Technical Specs


PSM 200 System

  • RF Carrier Frequency Range: 518¬-865 MHz (country dependent)
  • Modulation: FM +/- 35 kHz Deviation (Nominal)
  • Operating Temperature: -7 degrees C to +49 degrees C (+20 degrees F to +120 degrees F) 


P2T TransMixer

  • Modulation Limiter: Internal peak limiter (>10:1 hard knee compression)
  • Antenna: 1/4 Wavelength, semi-rigid, PCB Mount
  • Connector Type: XLR/1/4-inch combo
  • Nominal Input Level: -25 dBu @ 1/2 volume (12 o'clock)
  • Maximum Input Level: -5 dBu @ 1/2 volume (12 o'clock)
  • Current: 170 mA maximum
  • Dimensions: 220 mm x 140 mm x 40 mm (8.6 in. x 5.6 in. x 1.7 in.)
  • Net Weight: 370 g (13 oz.) 

    Audio Input
  • Connector Type: XLR/1/4-inch combo
  • Configuration: electronically balanced
  • Actual Impedance: 1 kΩ
  • Nominal Input Level: -25 dBu @ 1/2 volume (12 o'clock)
  • Maximum Input Level: -5 dBu @ 1/2 volume (12 o'clock)
  • Pin Assignments:
    XLR: 2=hot; 3=cold, 1=ground
    1/4: Tip=hot, Ring=cold, Sleeve=ground
  • Phantom Power Protection? Yes:Up to 52 Vdc

    Audio Output
  • Connector Type: XLR
  • Configuration: electronically balanced
  • Pin Assignments: 2 = hot ; 3 = cold, 1 = ground
  • Phantom Power Protection? Yes: Up to 52 Vdc


P2R Bodypack Receiver

  • RF Sensitivity: 109 dBm typical
  • Squelch Threshold: 102 dBm typical
  • Antenna: Attached Whip
  • Audio Input Connector: Connector Type: 1/4-inch Mono
  • Impedance: 1 MΩ
  • Maximum Input Level: LO = +0 dBu; HI = 10 dBu
  • Frequency Response: 30 Hz to 20 kHz (+/ 3 dB); earphone dependent
  • Power Requirements: 9 V alkaline battery, Duracell® type MN1604 recommended
  • Battery Life (Volume Dependent): 6 hrs (Wired) ; 4 hrs (Wireless)
  • Audio Output Connector: 1/8 inch (3.5 mm)
  • Minimum Load ImpedanceGo to the glossary: 8 Ω
  • Net Weight: 100 g (3.52 oz.), less battery
  • Overall Dimensions: 122 mm x 73 mm x 32 mm (4.809 in. x 2.875 in. x 1.251 in.)


SE112 Sound Isolating™ Earphones

  • Dynamic MicroDriver for great sound with deep bass and impressive sound isolation.
  • Fixed cables.